Marmitek PROTECTOR 28 Manual de usuario Pagina 1

MS9400/MS9700SECURITY AND HOME AUTOMATION SYSTEM

CONTROLS:1. CONTROL INDICATORSComes on when the remote control sends a radiosignal when keys are pressed. When the indicatorblinks only weakly, the ba

key. (e.g. living room lamp, TV, garden lights,etc.).8. BATTERY COMPARTMENT (BACK COVER)INSTALLATION:1. PLACING THE BATTERIESOpen the battery compartm

At the front of the modules, you’ll find 2 codeswitches: Unit Code (1 through 16) and HouseCode (A through O). Take care that when you areusing the mo

13MS9400/MS9700 5.PROGRAMMINGTHE SC2200 BASE STATION5.1 REGISTRATION OF RADIO SENSORSEvery sensor must be installed or registered with the base stati

Up to 8 remote controls can be registered with the base station (KR10/1 and SH624/1).1. Set mode switch to the INSTALL position: All indicators of occ

15MS9400/MS9700 5.4 PROGRAMMING TELEPHONE NUMBERThe Marmitek SC2200 base station has a standard telephone dialler. In case of a alarm, up to 4 teleph

16 MARMITEKThe alarm message of the telephone dialler can be recorded and re-recorded when required. The message can be up toapprox. 12 seconds. It is

17MS9400/MS9700 5.6 DELAY TIMESARMINGWhen arming the security system by means of the remote controls KR10/1 or SH624/1 in the ARM AWAY mode, the syst

18 MARMITEK5.7 JAMMING DETECTOR ON/OFFThe Marmitek SC2200 base station is equipped with a system to detect strong external interfering signal that may

19MS9400/MS9700 5.8 CHANGING YOUR PERSONALIDENTIFICATION CODEThis access code, is your Personal identification code. When you have changed this code,

2 MARMITEKINTRODUCTIONCongratulations! You purchased a Marmitek MS9700/9400 Security System.Marmitek Security Systems are quality products and are man

20 MARMITEK5.9 ERASING OF A REGISTERED SENSOR5.10 ERASING OF ALL SETTINGSIn case it is required, you can reset the base station to the factory default

INSTALL – Position for installing sensors and for changing system settings. RUN 1 – For normal alarm operation.RUN 2 – For normal alarm operation. Wh

6.3 WHEN AN ALARM SITUATION OCCURS• An alarm situation can only be detected when the SC2200 base station is armed• An instantaneous or delayed alarm i

The security system can be disarmed by means of the KR10/1 and SH624/1 remote control or by using your PIN on thekeyboard of the SC2200 base station.1

A panic alarm can be activated at any time in case of an emergency, regardless if the system is armed or disarmed.You can activate a panic alarm in th

25MS9400/MS9700 Your security system is equipped with a wide variety of functions to control lights, extra sirens, appliances and sunshades,throughou

FUNCTION ADDRESSESFunction: Address: With ref. address A1: With ref. address B3:Alarm light [HC+[UC] A1 B3All lights [UC] A BStatus Indicator [HC] + [

For using this function, you need the Glass BreakSensor GB10 (optional). This sensor contains aphotocell that (at dusk) starts a programsimulating you

28 MARMITEKThe security system does not operate:Check that the POWER indicator on the SC2200base station is on. If not, check that the PS500power supp

N.B.: When replacing the batteries of thesensor when the system is operational, you canmake sure that the sensor maintains its uniquecode avoiding re-

3MS9400/MS9700 1 GENERAL• Marmitek systems are designed for use in dry environments.• Avoid placement of system components in environments with extre

4 MARMITEK3 MARMITEK SYSTEMS3.1 COMPONENTSMARMITEK SYSTEMS CONSIST OF THE FOLLOWING PARTS:1 SC2200 SECURITY CONSOLE(BASE STATION)2 PS500 MAINS ADAPTOR

5MS9400/MS9700 4 INSTALLATION OF THE COMPONENTS4.1 SIGNALS AND RANGEYour security system is using variouscommunication techniques. For a goodundersta

4.2THE SC2200BASE STATION1. PANICWhen pressed, this red button initiates animmediate alarm.2. ARM HOMEAlarm function when being at home. Only doorand

7MS9400/MS9700 14. TIME OFFUsed to set the Lifestyle mode. When pressing thiskey at a certain time, the Lifestyle program will beswitched off every d

CONTROLS:1. CONTROLINDICATORWhen you pressthe button TEST, orwhen the unit istransmitting asignal to the basestation, thisindicator will come on. When

3. CODEBy pressing this key, the sensor gets a new code (1out of 65.536).N.B.: When the sensor has been installed on thesystem already, you have, afte