Marmitek PROTECTOR 28 Manual de usuario descargar pdf (Pagina 2)

2 MARMITEK

INTRODUCTION

Congratulations! You purchased a Marmitek MS9700/9400 Security System.

Marmitek Security Systems are quality products and are manufactured with

high precision.

The Marmitek Security System protects yourself and your home against

intruders. On top of that your Marmitek Security System can control lights

and appliances throughout your house (using the existing mains wires!). In

that way your Marmitek Security System can create a “lived-in look” when

you are away. Optional plug-in modules, wall switches or DIN-Rail modules

(at the distribution panel) allow switching of appliances or dimming of lights.

These modules can be programmed to be part of the alarm signalling.

Up to 16 wireless (radio) sensors can be installed onto the supplied Security

Console SC2200. This base station can be operated by up to 8 wireless

(radio) remote controllers. On top of that you can operate your Marmitek

Security System via the keyboard of the Security Console SC2200.

When an alarm situation occurs, the built-in telephone voice dialler of the

Security Console SC2200 will dial up to 4 pre-programmed telephone

numbers and play your pre-recorded alarm message. Anyone picking up the

phone on the other end responds to the alarm message by pressing a single

digit on that telephone. This will stop further dialling and allows the person

who picked up the phone to “listen-in“ to the protected premises by means

of the built-in microphone of the Security Console SC2200. Failing sensors

will be reported in a similar way by playing a fixed service message.

It is important that you carefully read through all of the chapters of this

users’ guide before starting the installation. Also when a third party is

installing the system for you, you have to read this manual carefully as it

contains important information regarding operation and use of the

Marmitek SC2200.

In case of any problems during installation or use of the system, please read

first through the troubleshooting chapter in the back of this users’ guide.

You also can contact the Martmitek web site (marmitek.com) for additional

information. In case you cannot fix the problem with these

recommendations, you then have to contact the dealer where you

purchased your Marmitek Security System.

CONTENTS

1. General 3

2. Safety Precautions 3

3. Marmitek Systems 4

3.1 Components 4

3.2 Important Features 4

4. Installation of the components 5

4.1 Signals and range 5

4.2 SC2200 Security Console (base station) 6

4.3 DS10 Door/Window Sensors 8

4.4 MS10 Motion Sensors 9

4.5 KR10/1 Key Fob Remote Control 10

4.6 SH624/1 System Remote Control (optional for MS9400) 10

4.7 LM12 Lamp Module (optional for MS9400) 11

4.8 Installation of other (wired) sensors 12

4.9 Installation of the GB10 Glass Break Sensor 12

5. Programming the SC2200 base station 13

5.1 Registration of radio sensors 13

5.2 Registration of wireless remote controls 14

5.3 Set siren on/off (silent alarm) 14

5.4 Programming of telephone numbers 15

5.5 Recording the alarm message 16

5.6 Delayed alarm times 17

5.7 Jamming detection on/off 18

5.8 Change personal identification code (PIN) 19

5.9 Erasing a radio sensor 20

5.10 Erasing of all settings 20

6. Operating the system 21

6.1 Install, Run 1 and Run 2 21

6.2 Arming the system 21

6.3 When an alarm situation occurs 22

6.4 Disarming the system 23

6.5 Disarming after an alarm (reset) 23

6.6 Panic alarm 24

6.7 Zone indicators 24

6.8 Controlling lights and appliances (Home Automation) 25

6.9 Lifestyle programming 27

7. Troubleshooting 28

1 2 3 4 5 6 7 ... 28 29

Comentarios a estos manuales

Sin comentarios

Marmitek PROTECTOR 28 Manual de usuario Pagina 2

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Marmitek PROTECTOR 28